fish Finder Tips
Modern fishfinders are much better at giving a clear image of what lies below with no input on your part. When it is zoomed in and properly tuned, your fishfinder will have the ability to discern the fish from the bottom when the fish is resting right on the bottom. All those new fish finders became smarter than people at figuring out where the fish are and it displays it on your LCD. But good as they are, they aren't perfect. You have to make sure they are adjusted properly to maximize it's ability to find fish.
What can you do to tune in your fish finder better? These fishfinder are certain to assist you in finding fish faster. Start in auto mode when you first go out fishing. Even in unusual circumstances, such as water with lots of turbulence or solids, auto mode will provide you with more information than if you were to try and guess. Which should eliminate the gobbledegook, which is normally the consequence of air bubbles near the surface. A clutter might be produced by the presence of substantial quantities of algae or plankton, So do not assume that every thing you see on the screen is fish. There is a lot of factors that can make objects on your screen. But, since these form the foundation of the food chain, around areas of surface, sometimes these clutter will help you locate fish. You can also have the ability to locate reefs or artificial barriers between different water masses by seeing a surprising and dramatic change in surface clutter, therefore seeing things near surface isn't always a bad thing, and you might want to think twice before tuning it out.
Begin by utilizing the traditional way of setting the sensitivity, tuning it all of the way down till the only thing on the screen is the bottom reading. Then, increase the gain until a secondary bottom echo appears beneath the bottom. Now you have a very good starting point. From here, if the screen is not relatively clean, then make fine adjustments. If theres clutter at the top only, adjust the STC setting. And if theres clutter everywhere, you will have to tone down the sensitivity some more but bear in mind that lowering it down from this point can also eliminate weak yields created by small fish, weeds, along with other items.
Dont try to tune out faint lines which seem under water at a fairly consistent depth. These are not clutter or false positive readings, they are thermoclines. These are temperature barriers, that have formed between different layers of water. Occasionally thermoclines show up as relatively thick lines and other times, they'll be a series of single dots. Sensitive units will typically show thermoclines while set at auto mode, but whether you have a very cheap or weak unit, you might have to improve sensitivity at order for them to appear.
What can you do to tune in your fish finder better? These fishfinder are certain to assist you in finding fish faster. Start in auto mode when you first go out fishing. Even in unusual circumstances, such as water with lots of turbulence or solids, auto mode will provide you with more information than if you were to try and guess. Which should eliminate the gobbledegook, which is normally the consequence of air bubbles near the surface. A clutter might be produced by the presence of substantial quantities of algae or plankton, So do not assume that every thing you see on the screen is fish. There is a lot of factors that can make objects on your screen. But, since these form the foundation of the food chain, around areas of surface, sometimes these clutter will help you locate fish. You can also have the ability to locate reefs or artificial barriers between different water masses by seeing a surprising and dramatic change in surface clutter, therefore seeing things near surface isn't always a bad thing, and you might want to think twice before tuning it out.
Begin by utilizing the traditional way of setting the sensitivity, tuning it all of the way down till the only thing on the screen is the bottom reading. Then, increase the gain until a secondary bottom echo appears beneath the bottom. Now you have a very good starting point. From here, if the screen is not relatively clean, then make fine adjustments. If theres clutter at the top only, adjust the STC setting. And if theres clutter everywhere, you will have to tone down the sensitivity some more but bear in mind that lowering it down from this point can also eliminate weak yields created by small fish, weeds, along with other items.
Dont try to tune out faint lines which seem under water at a fairly consistent depth. These are not clutter or false positive readings, they are thermoclines. These are temperature barriers, that have formed between different layers of water. Occasionally thermoclines show up as relatively thick lines and other times, they'll be a series of single dots. Sensitive units will typically show thermoclines while set at auto mode, but whether you have a very cheap or weak unit, you might have to improve sensitivity at order for them to appear.